Видео

This is the best explanation that I have seen on the Internet

How did you get 17?

I like your video and I want to learn I like your explanations more but the diagrams are not clearly seen the background and the colour of the drawing is not distinct add colours

Can you do a video on derating so many people don’t understand it’s of the wire insulation not the device terminal ratings electricians don’t understand you can use the 90deg column when derating

Amazing video access to power is golden

Great

Hello, I have wired my 3 phase motor per your video and used same components best to my knoledge, the issue I'm having is when I turn on my 120v brkr it pops. I looked over everything a phew times and can't see what's wrong. Any ideas. Thank you for your time.

Long story short multiply the gapping center to center times the shrinkage of whatever offset angle you are using, so 2 inch spacing with 30° offsets would have you advancing each mark a half inch on every pipe for your starting point. 🤘

Excellent tutorial keep up the great Work

Very well done!😊

Thank you

Thanks for the video but let's save some time 1/2 tangent of your degree x gap of pipe. Add or subtract from your 1st mark depending on if it's the shortest or longest your starting with. Also this should work the same for kicks

Is this the 2nd part of something? Where's the black wire come from why are there 2 reds and 2 greens? Those you've described well,but not the grey thing with 20+ places for wires to go

Paint the edges of the feet on your stand white to match the rest

great video!n

I love this channel...great information and really nice/fun guys who know how to relay info...

so in the angle pull we still had to size up the box to get 12 inches between raceway?

Greate video and explanations. By any chance would you be able to put out a bill of material on all the components you used in this video. I'm looking to wire my garage elevator in this manner. One switch downstairs one upstairs and one on the lift.

So I have a question, Why don't u have to account for the cross-section area when u put all the numbers in. Was it because it was already account for in the code book?

Good job

What app are you using sir?

Should also make sure that your multimeter is rated for the voltage/ amperage you're measuring. If the multimeter isn't rated appropriately it could cause death.

More videos please!

For the purposes of the viewer you should put a piece of blue tape on the motor shaft so we can see the motor reverse directions. Great video.

By far best explanation

Is table 8 is only applicable in DC system?

Ive had to check a lot of these. I would check the overload for tripping first. Then the 480 V fuses and then the motor for grounds. I found that rarely did the control circuit had problems.

It's called motor pluging foward to reverse not a problem 21:10 21:10

Great Video! What software are you using for your example?

By far one of the best instructors on RUclips right now coming from a Utah Journeyman

Motor control forward start yellow stop off reverse green switch power teacher ji

The moving photo of the women was distracting, childish and unnecessary. Just talk about the formulas. We don't need or want a show, we want an explanation.

Does anyone know what software is being used for the simulation?

Timer motor power start stop off emergency reset teacher ji

ba- LA - kla - va

SAME AS CEC CANAD CODE BOOK NICE

Making it easier s not a problem why don’t you show them how to measure for a concentric bend in the field

Great video, however I have a suggestion. Use a digital protractor on the long side of the pipe , zero it, than after your first bend test the bent end for 30 degrees. Also note the spring back and write it down for the next guy. For example you might have to bend a 33 degree bend for a perfect 30. Thank you for your video.

When you were testing the power button, where dod you have your red meter lead?

Great information and well taught

And what about you having 2 sets of conductors with Z method? Please Help!!

I have 4 mixer motors at a WWTF. I have had to turn the yellow amp adjustment from 8 to 14 amps to keep them running with out tripping. 1 of of them however now runs for 1-3 mins then trips everytime. Pulled and megged motor. It is good. Voltage is good and consistent with other mixer motors. I have not seen Amps above 7 on anyof the motors including the one tripping. Any suggestions? Going in circles with Evoqua. Plant is 1 year old. All ran good first 6 months then developed issues after that.

You're using 10amps for VFD and motor control yet say that 10amp relay not to be used with anything requiring a load? 10amp is the common rating for general residential use, lights and power points, here in Australia.

This guy explains everything so well

You still need some electrical knowledge to understand this video. I know almost nothing and get lost after he adds the bridges. More detail on components is needed.

I always teach to only swap A & C phase to reverse the phase rotation. This prevents accidentally burning stuff up in the rare time one may have to deal with the high leg on a 120/240 3 phase feed. (Code here is the high leg must be on B Phase)

4th year apprentice here , thanks for the smooth video 👌

dude this is amazing, thank you so much. having an ACTUAL MOTOR is going next freaking level. thank you.

Why does the neutral have to go through the overload relay and not just straight to the coil (A2)?

AWSOME VIDEO